Concrete, land clearing, site prep, pools and metal buildings in HoustonConcrete and site work in Houston, TX
Call or text (888) 795-7757 20+ years of experience
SETX Construction
Concrete contractor, land clearing and site prep in New Caney, TX
Call (888) 795-7757 Request a Quote

How Much Does a Concrete Driveway Cost in Texas?

National cost guides put a new concrete driveway at about $6 to $15 per square foot. One guide lists $2,400 to $8,600 for a two-car driveway. That range covers plain gray concrete and basic decorative finishes. Another guide puts the typical project at $1,885 to $6,475.

These guides publish national figures, so read them as a starting band for Texas. The size of the driveway and its finish move the real number. These are market numbers, not our price list. Our concrete driveway work covers driveways, approaches, walks and patios on the northeast side of Houston.

What does a concrete driveway cost per square foot?

One national guide splits its $6 to $15 into $3 to $7 for labor and $3 to $8 for materials. Its totals by size, for standard to basic finishes, look like this.

Driveway sizeSquare feetPublished total range
1-car, 10 by 20 feet200$1,200 to $3,000
1-car, 12 by 24 feet288$1,700 to $4,300
2-car, 20 by 20 feet400$2,400 to $6,000
2-car, 24 by 24 feet576$3,500 to $8,600
3-car, 24 by 36 feet864$5,200 to $13,000

A cost calculator site listed a starting national average of $9.59 to $11.78 per square foot in May 2026. That figure leaves out base work and demolition.

How much more does a stamped or decorative finish cost?

Most driveways get a broom finish, one guide says. A broom dragged across the wet concrete leaves a light texture for grip. One national guide sorts finishes into four price tiers.

Finish tierPublished cost per square footWhat it usually means
Standard$6 to $10Plain gray concrete with a broom finish
Basic decorative$10 to $15One stain color, a simple border or exposed aggregate
Mid-range$15 to $20A stamped pattern in two or three colors
High-end$20 to $25 or moreSeveral patterns and colors with custom borders

The same guide prices a stamped driveway at $8 to $26 per square foot. Its top end includes colored concrete. Another guide lists stamped concrete at $8 to $15 per square foot. We pour stamped and decorative finishes on request.

What does a concrete patio cost?

Concrete patios are priced by the square foot too. One national guide puts a plain concrete patio at $4 to $12 per square foot installed. A basic 20 by 20 foot patio comes to $1,600 to $4,800 in that guide.

A broom finish runs $6 to $13 per square foot, and exposed aggregate runs $7 to $18. Stamped patios run $9 to $30. The guide calls 4 inches the standard thickness for a home patio.

How do thickness and steel change the price?

One national guide says a home driveway should be at least 4 inches thick for standard vehicles. For RVs and other heavy vehicles, it says 5 to 6 inches, with edges of 6 to 8 inches.

ThicknessPublished cost per square footTypical use
4 inches$6 to $15Standard vehicles
6 inches$8 to $20Heavy vehicles

Another guide says 2 more inches of thickness can raise the cost by about 25 percent. Rebar or wire mesh adds $1 to $3 per square foot in both guides. One of them says rebar improves crack resistance.

The ground under the driveway is the local factor. Heavy clay covers the prairie around Crosby and Huffman and much of Liberty County. The federal soil survey says Lake Charles clay cracks up to 2 inches wide as it dries. Locals call it gumbo.

To the north, around Kingwood, Porter and Conroe, the ground turns sandier under the pines. Our Texas concrete slab cost guide covers the clay in more depth.

An RV or a tractor can also park on its own pad. Our page on concrete slabs for RVs and equipment has more on that work.

What does it cost to tear out an old driveway?

Tearing out an old driveway adds to the cost of the new one. One national guide puts removal at $2 to $6 per square foot. Another page from the same guide lists $1 to $3, haul-off included. A second guide prices a whole tear-out at $1,500 to $2,500.

For a 400 square foot driveway, $1 to $6 per square foot comes to $400 to $2,400. One guide says the cost of a redo also depends on whether the old base can be reused. Ask for the tear-out and the new pour as separate lines on the quote.

What changes the cost of a long driveway on acreage?

Length drives the total on acreage. A 12-foot-wide lane holds 12 square feet in every running foot. At $6 to $15 per square foot, that is $72 to $180 per running foot. A 300-foot drive covers 3,600 square feet, or $21,600 to $54,000 by the same math.

Two notes from one national guide pull in opposite directions. Bigger driveways often cost less per square foot. Delivery often costs more in rural areas.

The ground along the route adds its own lines. Brush and small trees may have to come out first. The path also needs land grading so water drains off before the forms go up.

Cost linePublished market rangeKind of source
Digging out plants, soil and small trees$1 to $5 per square footnational cost guide
Grading and site prep$3 to $8 per square footnational cost guide
Drainage trenches or channels along the drive$400 to $2,400national cost guide
Driveway permit, where one is required$50 to $200national cost guide

Who decides the culvert where your driveway meets the road?

Where a road has an open ditch, a driveway crosses it on a culvert pipe. The address decides which office sets the rules: the city inside its limits, the county outside them.

Harris County’s engineering office calls the strip between your property line and the street the right-of-way. Any driveway or culvert there needs a county permit. The county’s 2025 driveway rules leave the culvert size to the County Engineer. The pipe stays uncovered until the county inspects it.

In Montgomery County, the county’s permit FAQ sends culvert questions to your commissioner precinct. In Precinct 4, an inspector visits the site and sets the pipe size. The owner puts the pipe in, or hires it out, and calls for an inspection before it is covered.

Liberty County’s culvert instructions say to call the permit department or your commissioner to verify the size first. The county may remove a culvert that has no permit.

Inside a city, the city’s rules apply. Humble’s 2019 design manual, for one, calls for at least 18-inch reinforced concrete pipe on ditch streets. On a state highway, TxDOT’s access manual sends the driveway permit through the local TxDOT district office.

The culvert is a cost line apart from the concrete. The permit office for your road answers the culvert question, and we point you there.

What is the next step for your driveway?

Measure the length and width you have in mind. Note what will park on it, and whether an old driveway has to come out first.

SETX Construction works about 40 miles around northeast Houston. We pour concrete driveways and patios for homes and acreage. We look at the site and give you a free estimate, with the quote in writing. Call (888) 795-7757.

Frequently asked questions

How much does a 2-car concrete driveway cost?
One national cost guide puts a 20 by 20 foot driveway at $2,400 to $6,000. Its 24 by 24 foot driveway runs $3,500 to $8,600. Both figures are for standard to basic finishes.
How much does a concrete patio cost?
One national guide puts a basic 20 by 20 foot concrete patio at $1,600 to $4,800. Plain concrete runs $4 to $12 per square foot installed in that guide. Stamped patios cost $9 to $30 per square foot.
How thick should a concrete driveway be?
One national cost guide says at least 4 inches for standard vehicles. For RVs and other heavy vehicles, it says 5 to 6 inches, with edges of 6 to 8 inches. The same guide prices 6-inch concrete at $8 to $20 per square foot.
How long before I can drive on a new concrete driveway?
One national guide says you can walk on it after 24 to 48 hours. It says to wait at least 7 days before you drive on it. For heavy vehicles, it suggests waiting for the full cure, about 28 to 30 days.
Is tearing out the old driveway part of the price?
Tear-out adds to the cost of the new pour. National cost guides put tear-out and haul-off at about $1 to $6 per square foot. Ask to see it as its own line on the quote.
Do I need a permit or a culvert for a new driveway?
The address decides which office you call. On a Harris County road, a driveway in the county right-of-way needs a county permit. On a state highway, the permit comes from the local TxDOT district office. The permit office for your road answers the culvert question, and we point you there.
Is this what SETX Construction charges?
No, these are market numbers from national cost guides, not our price list. Your driveway's size and the ground under it set the real number. We look at the site and give you a free estimate, with the quote in writing. Call (888) 795-7757.
Request a Quote

Get In Touch With SETX Construction

Send the form with the job you have in mind and where the property is. Or call (888) 795-7757 and ask for a free estimate.

  • Call or text (888) 795-7757
  • Serving Houston, TX and the northeast side of the metro
  • Free written estimates · concrete, land work, pools and metal buildings

Request a Quote

Tell us about the driveway, slab, land, pool or metal building and where it is. We look at the job and give you a free estimate in writing.

Call (888) 795-7757